This post following next relating to How to Install a Bathtub Yourself is incredibly fascinating. You should look it over.
Mounting a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably difficult project. If the old tub is readily available, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as fit attempting it. Instead of employing a specialist to take over a halfway-completed job, it is better to consider employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you install a brand-new bath tub in your shower room if you have actually already purchased a new bathtub and also do not need to change the arrangement of your previous water supply pipelines.
Your devices as well as material checklist need to consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines are in area between the tap and also the sink. Secure the tap in position with the manufacturer offered backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous kind should be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Making use of both wood boards under its feet, position the bathtub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply and check all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub must wait up until the tub has actually been utilized a minimum of once as this will settle it right into its last placement.
Planning for the Installment
First of all, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads about How to Install a Bathtub, I figured sharing that excerpt was important. Loved our entry? Please share it. Help another person find it. I thank you for reading our article about How to Install a Bathtub Yourself.
Contact Us Today